Comments for Vinyl Cutters For Sale

Comment on 5 Minute Sign Making by Mike

Mike — Sun, 25 Jul 2010 13:27:39 +0000

Thanks for the demo.

It got me started.

Regards
Mike

Australia.

Comment on How to Setup Your CR-630 or CR-1200 by ProCut by Lyndsey

Lyndsey — Fri, 31 Jul 2009 04:23:29 +0000

These are supposed to be compatible with Mac right? How does that setup work?

Comment on New Vinyl Cutters From ProCut by Ryan

Ryan — Tue, 27 Jan 2009 20:26:35 +0000

i noticed these have much more cutting force than any other brand cutter. i plan on cutting thicker polypropylene so this looks like a good bet.

Comment on Refine Cutter Not Tracking in the Y Axis (When Cutting Vertically) by admin

admin — Tue, 30 Dec 2008 01:48:43 +0000

Adjusting the pinch rollers on the CR-630 is easy. Under the handle is a brass screw. The amount this screw is screwed down determines the tension. More important than the tension (Though it is important) is that both of them are even with each other.

Josh

Comment on How to Setup Your CR-630 or CR-1200 by ProCut by I`m in Tears :( Creation CR630 vinyl cutter Error: LoadLibrary PcutLib.DLL - Page 8 - T-Shirt Forums

Tue, 21 Oct 2008 05:26:18 +0000

[...] Re: I`m in Tears Creation CR630 vinyl cutter Error: LoadLibrary PcutLib.DLL 1) DONT HOLD THAT SWITCH IN. It will make the cutter think a fault has occurred. If the carriage is against it, the cutter will not boot. 2) Check your Baud setting in sign cut vs. the Baud setting on the cutter Check out these steps also: Cheap Vinyl Cutters Blog Archive How to Setup Your CR-630 or CR-1200 by ProCut [...]

Comment on HASP Key Drivers for Flexi Apprentice by I`m in Tears :( Creation CR630 vinyl cutter Error: LoadLibrary PcutLib.DLL - Page 7 - T-Shirt Forums

Mon, 20 Oct 2008 05:52:13 +0000

[...] of the USB driver for the key for flexi. They can be somewhat persnickety. Here is the link: ProCut CR-630 HASP Key Drivers Feel free to message me, I’d be happy to help you anyway I can. Take any advice you get on a [...]

Comment on Refine Cutter Not Tracking in the Y Axis (When Cutting Vertically) by DL

DL — Sat, 17 May 2008 13:47:39 +0000

How do you adjust the tension of the pinch rollers?

Comment on Refine Cutter Not Tracking in the Y Axis (When Cutting Vertically) by DL

DL — Sat, 17 May 2008 12:29:16 +0000

How do you 1) change the pinch rollers and 2) make sure the blade is offset properly?

Comment on How to Setup Your CR-630 or CR-1200 by ProCut by ShaneC

ShaneC — Sat, 02 Feb 2008 19:56:40 +0000

I did all these steps to the letter and mine works, but if i send it anything latge or complex it cuts part of it then just stops and says “waiting…” on the LCD.

Also my only options when selecting the plotter are :
Creation-PCut>
CT-1200
CT-1500
CT-630
CT900
CTN-1200
CTN-1500
CTN-630
CTN-900

Are the CT-630 and CR-630 the same thing ?

Please help!

Comment on Tracing Bitmap Images in Adobe Illustrator CS2 by Christian

Christian — Sat, 17 Nov 2007 20:09:15 +0000

You can also upload the image to http://vectormagic.stanford.edu and have it do the conversion to vector format.
It’s very good.